modocrat
Well-known member
The kids on Monday morning: "We don't have any school uniforms to wear today!!"Excellent work as always! Well impressed with the quantity of pegs you "stocked up" on from your wife
-
Read the WELCOME ALL BMWFANATICS post.
Gavsadler’s 1st Classic, and a South African Special
- Thread starter gavsadler
- Start date
Benji
Well-known member
Meanwhile the uniforms are chilling in the gutter after the wind blew them off the line, Gav doing his best to look innocent
gavsadler
///Member
Let me crack on with the updates:
Elsewhere, there is a thread about 90s cars, and mention is made of the maintenance required. I'll add my 2c here for now. So during my intermittent drives, I noticed the temperature gauge getting hotter than normal. Thankfully I was not far from home, so idled back home and parked. Investigations pointed to the radiator fan not coming on, due to one of the plug wires on the temperature switch had popped off. Anyway, reconnected that, and the fan was working again as intended. This was simple enough, however further checks revealed that the coolant bottle was split in 2 places and leaking. I suspect the increased temperature in the system caused this issue to become more pronounced.
The ex-owner had a spare coolant bottle, and it was part of the sale agreement, so again this was a quick 30min repair.
I also removed the bonnet lining, and thereafter gave the underside of the bonnet, and the engine bay it's first proper clean:
Moving onto some mechanical maintenance, the car was due for it's annual oil change, so I took care of that and cleaned the (K&N) panel air filter.
Next up, time to bleed the brakes. I was not sure when last it was done, although the colour of the fluid which came out points towards yonks ago.
I have an issue with the ABS light showing in the cluster, which I initially thought was a broken rear sensor, although after repairing the wiring, the fault persisted. Next plan was to replace both front sensors (to be done later on, I still needed to source an additional sensor).
For reference, the top sensor is for the rear wheels, and the bottom sensor is for the front wheels:
The rest of the wheels and tyres were also thoroughly cleaned and polished / coated / treated before going back onto the car (these too have not had a "wheels off" clean in quite some time):
Elsewhere, there is a thread about 90s cars, and mention is made of the maintenance required. I'll add my 2c here for now. So during my intermittent drives, I noticed the temperature gauge getting hotter than normal. Thankfully I was not far from home, so idled back home and parked. Investigations pointed to the radiator fan not coming on, due to one of the plug wires on the temperature switch had popped off. Anyway, reconnected that, and the fan was working again as intended. This was simple enough, however further checks revealed that the coolant bottle was split in 2 places and leaking. I suspect the increased temperature in the system caused this issue to become more pronounced.
The ex-owner had a spare coolant bottle, and it was part of the sale agreement, so again this was a quick 30min repair.
I also removed the bonnet lining, and thereafter gave the underside of the bonnet, and the engine bay it's first proper clean:
Moving onto some mechanical maintenance, the car was due for it's annual oil change, so I took care of that and cleaned the (K&N) panel air filter.
Next up, time to bleed the brakes. I was not sure when last it was done, although the colour of the fluid which came out points towards yonks ago.
I have an issue with the ABS light showing in the cluster, which I initially thought was a broken rear sensor, although after repairing the wiring, the fault persisted. Next plan was to replace both front sensors (to be done later on, I still needed to source an additional sensor).
For reference, the top sensor is for the rear wheels, and the bottom sensor is for the front wheels:
The rest of the wheels and tyres were also thoroughly cleaned and polished / coated / treated before going back onto the car (these too have not had a "wheels off" clean in quite some time):
gavsadler
///Member
In the meantime, my new headlights and indicators had arrived, so it was time to get round to fitting them.
Last view of "Before" (also with now-removed bumper badge):
Headlights removed, and some wiring to tidy up:
Ready for the new lights to be installed (also after cleaning in and around the area):
I wanted to get some decent bulbs, so opted for these Philips items, they even have blue park lights, lol:
Drum roll please, and a big sigh of relief and satisfaction:
A couple of days later, we were at another weekend, and as such, time to spend a day doing some exterior detailing. I used my trustworthy combination of TRC, Menzerna, P&S and Solution Finish products.
Here is the front left fender before polishing, the sun inspection light was not very round at all, more like a splat in the swirls and scratches:
I decided to try Menzerna Cut Force Pro only, it has 9/10 cut and 9/10 gloss. This was after a couple of passes:
The actual sun looking good:
Overall the paint came out very nicely. A massive improvement on before, much less scratches and swirls, and it removed some of the dull oxidised paint which was looking off-white. I reckon it's probably around 70% - 80% now. Next time I polish, I will use a finishing polish, no more cutting needed I don't think.
Then, one of my biggest transformations, the black trim. Solution Finish is my go-to product for this type of work. The results speak for themselves.
After cleaning with IPA:
1 coat of Solution Finish applied, this was about 5mins after application:
I leave the product to dwell for around 10mins, before doing final wipe off. The pics below are after final wipe off, rubbing my fingers across both areas, they come back clean, there is no product transfer, or crappy silicone surface coating to worry about.
And once all is said and done, nothing like a few pics of the exterior to end off a hard day's work:
Last view of "Before" (also with now-removed bumper badge):
Headlights removed, and some wiring to tidy up:
Ready for the new lights to be installed (also after cleaning in and around the area):
I wanted to get some decent bulbs, so opted for these Philips items, they even have blue park lights, lol:
Drum roll please, and a big sigh of relief and satisfaction:
A couple of days later, we were at another weekend, and as such, time to spend a day doing some exterior detailing. I used my trustworthy combination of TRC, Menzerna, P&S and Solution Finish products.
Here is the front left fender before polishing, the sun inspection light was not very round at all, more like a splat in the swirls and scratches:
I decided to try Menzerna Cut Force Pro only, it has 9/10 cut and 9/10 gloss. This was after a couple of passes:
The actual sun looking good:
Overall the paint came out very nicely. A massive improvement on before, much less scratches and swirls, and it removed some of the dull oxidised paint which was looking off-white. I reckon it's probably around 70% - 80% now. Next time I polish, I will use a finishing polish, no more cutting needed I don't think.
Then, one of my biggest transformations, the black trim. Solution Finish is my go-to product for this type of work. The results speak for themselves.
After cleaning with IPA:
1 coat of Solution Finish applied, this was about 5mins after application:
I leave the product to dwell for around 10mins, before doing final wipe off. The pics below are after final wipe off, rubbing my fingers across both areas, they come back clean, there is no product transfer, or crappy silicone surface coating to worry about.
And once all is said and done, nothing like a few pics of the exterior to end off a hard day's work:
gavsadler
///Member
To end off the updates for May, while the bonnet lining was removed, I gave it a though clean and left it to dry flat in the sun for about a week. It actually came out better than expected.
There is a nasty hole in the lining, just above the turbo, I suspect 34 years of heat and water have done the damage. I had a go at fashioning an aluminium heat shield to cover this area, which looked good in principle, but was not going to work. The weight caused the lining to sag and the heat shield in turn was touching the valve cover, so I have since removed the aluminium piece. If I can find a nice replacement bonnet lining, that would be first prize, but I suspect I will be looking for a looooong time.
There is a nasty hole in the lining, just above the turbo, I suspect 34 years of heat and water have done the damage. I had a go at fashioning an aluminium heat shield to cover this area, which looked good in principle, but was not going to work. The weight caused the lining to sag and the heat shield in turn was touching the valve cover, so I have since removed the aluminium piece. If I can find a nice replacement bonnet lining, that would be first prize, but I suspect I will be looking for a looooong time.
gavsadler
///Member
Upates June-2026:
June was a much quieter month in terms of updates. The bulk of the initial bugbear work was done, and the car was getting to a place where I was more comfortable driving it.
Back to the interior, and time for some gauge deletes. I disconnected the boost gauge and AFR gauge. I was comfortable knowing what the car is boosting (around 0.6-0.7bar) and the AFR range it operates in for mixtures (14.4 at idle or light load, and dropping to around 12.2 under full load).
A crude, yet surprisingly effective mounting bracket, lol:
A clean dash once again:
While I was there, I cleaned the steering wheel. It must be said, I think a lot of this is tired leather coming off, as opposed to outright dirt:
I received good news that my badges were being wrapped up. Here's a pic of them being made:
And a couple of weeks later, the finished items arrived. Woo-hoo, I can redeem myself from my stupid paint stripper antics from a month ago.
Installation of the badges, in the correct place as per OEM:
Old vs New:
I also managed to source another front ABS sensor. This seems to be a critically endangered part. We had a good chuckle on the day. I went to one of my (relatively) nearby Goldwagens, their system showed 1 in stock. The shop assistant went to search for it in the back. A few moments later, we hear a flurry of exclamations and what sounds like disbelief. When she got back to the counter, we understood what she was so surprised about.
Check the date stamp on the box, this is when it was booked into stock at this particular Goldwagen: January 2008! It's been sitting on the shelf for 18 years! Definitely a parts barn find of sorts. Check out the dust on the part itself, in a closed box:
With 2 sensors handy now, I would be able to tackle the ABS issue in the not-so-distant future.
But before we get to that, it would be time to enjoy the car a bit at it's first event. That will be in the next update...
Thanks for reading...
June was a much quieter month in terms of updates. The bulk of the initial bugbear work was done, and the car was getting to a place where I was more comfortable driving it.
Back to the interior, and time for some gauge deletes. I disconnected the boost gauge and AFR gauge. I was comfortable knowing what the car is boosting (around 0.6-0.7bar) and the AFR range it operates in for mixtures (14.4 at idle or light load, and dropping to around 12.2 under full load).
A crude, yet surprisingly effective mounting bracket, lol:
A clean dash once again:
While I was there, I cleaned the steering wheel. It must be said, I think a lot of this is tired leather coming off, as opposed to outright dirt:
I received good news that my badges were being wrapped up. Here's a pic of them being made:
And a couple of weeks later, the finished items arrived. Woo-hoo, I can redeem myself from my stupid paint stripper antics from a month ago.
Installation of the badges, in the correct place as per OEM:
Old vs New:
I also managed to source another front ABS sensor. This seems to be a critically endangered part. We had a good chuckle on the day. I went to one of my (relatively) nearby Goldwagens, their system showed 1 in stock. The shop assistant went to search for it in the back. A few moments later, we hear a flurry of exclamations and what sounds like disbelief. When she got back to the counter, we understood what she was so surprised about.
Check the date stamp on the box, this is when it was booked into stock at this particular Goldwagen: January 2008! It's been sitting on the shelf for 18 years! Definitely a parts barn find of sorts. Check out the dust on the part itself, in a closed box:
With 2 sensors handy now, I would be able to tackle the ABS issue in the not-so-distant future.
But before we get to that, it would be time to enjoy the car a bit at it's first event. That will be in the next update...
Thanks for reading...
///M Individual
Well-known member
Mine too! Well done Gav!
gavsadler
///Member
Aaaaand the last update for the month of June-2026:
With lots of work having been done on the car, it was about time to enjoy it a little bit. In typical Sadler tradition, it was time to visit the Skidpan again. It's been almost a solid year since I last attended an event (due to sad circumstances outlined earlier on), so there was a bit of apprehension and a gloomy atmosphere. Nevertheless...
My daughter wanted to attend again, as well as her friend; A good way to kick off the school holidays. They initially thought we were going in the M3, and were somewhat dismissive of this old car we ended up going in, but that opinion would change later on...
We headed off to Waterfall at a fairly relaxed pace, not giving anything away. This was also my daughter's first long trip in the car. Just before the highway exit, I gave it some beans up the hill in 4th gear, and checking in the mirror I was greeted with some big eyes, lol.
After the usual briefings, we got things underway. We did 6 runs, with the best 5 counting. The first 2 runs I took things easy, learning the car and how it feels. After that I started to push a little more, and I was actually quite impressed with how the car handled. It's light, it's low to the ground, and the LSD does wonders around the cones, it really does pull the front end around, completely different to my Ute where understeer sets in fairly quickly.
I actually ran out of talent on what was the 3rd run I think. Doing one of the fastest sections of the course (the first half of the big O), the tyres were protesting a bit as we headed to the cone to sweep around it. All of a sudden, as we arrived at the apex, the tyres found some grip, and at the same time, the diff decided that with this newfound grip, it could also work again and pull the car in tighter. A split second later, and there was a dull thump as the inside wheel hooked the cones. I was caught out. After this run, some reflecting on the pavement made me think this probably happened to many TS owners back in the day, shortly before the binned it in spectacular fashion. Thankfully the skidpan is a safe, controlled environment to learn and practice these things.
Anyway, enough talking. For what it's worth, got 3rd place for the FWD category, but had good fun. I will definitely consider taking the car back to a future event.
Some pics and vids below:
As we head into July, some niggles have cropped up (90's cars....), which are sucking up my attention and focus. More on that in the next update....
With lots of work having been done on the car, it was about time to enjoy it a little bit. In typical Sadler tradition, it was time to visit the Skidpan again. It's been almost a solid year since I last attended an event (due to sad circumstances outlined earlier on), so there was a bit of apprehension and a gloomy atmosphere. Nevertheless...
My daughter wanted to attend again, as well as her friend; A good way to kick off the school holidays. They initially thought we were going in the M3, and were somewhat dismissive of this old car we ended up going in, but that opinion would change later on...
We headed off to Waterfall at a fairly relaxed pace, not giving anything away. This was also my daughter's first long trip in the car. Just before the highway exit, I gave it some beans up the hill in 4th gear, and checking in the mirror I was greeted with some big eyes, lol.
After the usual briefings, we got things underway. We did 6 runs, with the best 5 counting. The first 2 runs I took things easy, learning the car and how it feels. After that I started to push a little more, and I was actually quite impressed with how the car handled. It's light, it's low to the ground, and the LSD does wonders around the cones, it really does pull the front end around, completely different to my Ute where understeer sets in fairly quickly.
I actually ran out of talent on what was the 3rd run I think. Doing one of the fastest sections of the course (the first half of the big O), the tyres were protesting a bit as we headed to the cone to sweep around it. All of a sudden, as we arrived at the apex, the tyres found some grip, and at the same time, the diff decided that with this newfound grip, it could also work again and pull the car in tighter. A split second later, and there was a dull thump as the inside wheel hooked the cones. I was caught out. After this run, some reflecting on the pavement made me think this probably happened to many TS owners back in the day, shortly before the binned it in spectacular fashion. Thankfully the skidpan is a safe, controlled environment to learn and practice these things.
Anyway, enough talking. For what it's worth, got 3rd place for the FWD category, but had good fun. I will definitely consider taking the car back to a future event.
Some pics and vids below:
As we head into July, some niggles have cropped up (90's cars....), which are sucking up my attention and focus. More on that in the next update....
Gordvisr
Well-known member
Looks like tons of fun. These cars can get grippy, handle very well and then suddenly not. Really love what you doing with this car. My X brother in law had one, he drove it every day (Owned it more than ten years), was sold for 45K three years ago, i missed the sale a few moments.
individj
Well-known member
awesome holiday fun wow
WIDEOPN-X5
Well-known member
When one Googles "Terminal Understeer", does this pic come up??😂😂
PS I am just kidding. Watching the video clip it is actually pretty good for a powerful front driver.
